ASTM A924/A924M, 2020 Edition, September 1, 2020 - Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process This specification covers the general requirements that, unless otherwise specified in the product specification, apply to steel sheet in coils and cut lengths, metallic-coated on continuous lines by the hot-dip process. Aluminised Steel Coil and Sheet- heat resistance and safe Product Specification and Steel Grade ASTM JIS AISI EN Mills Standard Specification A240 SA240 G4304 G4312 10088-2 17224, 17440 ,17441 0.00328 Grade S30400 S30403 S31603 S43000 S44400 SUS304 SUS304L SUS316L SUS430 SUS444 304 304L 316L 430 444 1.4301 1.4306 1.4401 1.4016 1.4521 201 202 204Cu3; Cold Rolled; Sheet and Plate; Floor and Chequered
Coil ID/Min Sheet length(mm) 508 and 610:Coil OD/Max Sheet length(mm) 1800:Coil Pkt Wt(MT) 20 MT Max:Product Quality:Commercial Soft Lock Forming Quality Deep Drawing Extra Deep Drawing/IF Full Hard Bending and Forming Structural Grade:Coating type:ALU-ZINC:Standards:JIS:G:3321,EN10215,ASTM:A792 GALVALUME STEEL - Alstro StriveCoil ID/Min Sheet length(mm) 508 and 610:Coil OD/Max Sheet length(mm) 1800:Coil Pkt Wt(MT) 20 MT Max:Product Quality:Commercial Soft Lock Forming Quality Deep Drawing Extra Deep Drawing/IF Full Hard Bending and Forming Structural Grade:Coating type:ALU-ZINC:Standards:JIS:G:3321,EN10215,ASTM:A792 ISO 3574 Deep Drawing Quality Cold Rolled CR3 SteelJan 03, 2013 · CR3 steels are deep drawing quality mild steel implied in ISO 3574 and is classified equivalent to SPCE steels in JIS standard. CR3 Steels are applicable for deep drawing processes that are applicable for minimal extend. Deep drawing processes are those where depth of drawn part is more as compare to the diameter of the part to be drawn
JIS G3131 Hot-roll mild steel plates, sheet and strip 1. Scope The Japanese Industrial Standard specifies the hot-rolled mild steel plates, sheets and strip (hereafter referred to as "steel sheet and coil")intended for general fabrication purposes and drawing. Remarks 1. The standards cited in this Standard are given in Attached Table 1. 2. JIS G3131 PDF - jobsinphilippinesfoOct 25, 2020 · The steel sheets which are not bundled shall be marked for jie sheet. Report in JIS G when required by the purchaser in advance. In JIS, the number of the standard can be replaced by the symbol of grade. Please read article completely. For the steel sheet and strip under 40 mm in width, measurement shall be made at the mid-width thereof. Prepainted Steel Sheet with Silicon Polyester - BARO METALPrepainted Steel Sheet with Silicon Polyester Product Description - Prepainted steel sheet is coated and baked with paint containing silicon resin. - It is a popular construction material because of its highly weather resistant properties. - Countries, including Korea, that have industrial complexes along their coastal regions will find it more economical to use steel plates coated with Si-P/E
Japanese Industrial Standard (JIS) Classification Designation Characteristics and Application Defined electrogalvanized steel sheets from structural quality to deep drawing quality, from Silicon steel is the most important soft magnetic material in use nowadays. Product Fields BCCJapanese Industrial Standard (JIS) Classification Designation Characteristics and Application Defined electrogalvanized steel sheets from structural quality to deep drawing quality, from Silicon steel is the most important soft magnetic material in use nowadays. Product Standards - POSCOKS & JIS Standards Two types of zinc coating weights, that is, the same weight on both sides and differentiated weights on each side, are applied to the steel sheets and steel coils. The standard and minimum Zn coating weights are marked with a code combining the coating weight of each side while dividing two weights with a slash (/).
Related products :SPCEN steel, SPCD steel, SPCC steel SPCE eed deep drawing cold rolled carbon steel sheet and strip, equivalent to China 08AL (5213) deep drawing steel. When the need to ensure non-timeliness in grades at the end plus N is SPCEN. Slit EdgeStainless Steel Metal Sheet Full Hardness To Deep Slit EdgeStainless Steel Metal Sheet Full Hardness To Deep Drawing . Description:STAINLESS STEELS are iron-base alloys that contain a minimum of about 12% Cr,the amount needed to prevent the formation of rust in unpolluted atmospheres (hence the designation stainless). deep draw steel, deep draw steel Suppliers and DX53D+AS Deep Drawing Aluminium silicon Alloy Coated Steel ASTM A634 Aluminized Steel Coil JIS Standard SPCD cold rold steel coil/deep drawing cold rolled steel coils sheet from website business DC06 St16 St17 08AL Deep Drawing Cold Rolled Steel Coil/sheet . US $500.00-$
High strength and highly formable HR steel sheet and plate is also easy to drill, form and weld. Hot Selling Deep Drawing JIS Standard Silicon Steel SheetHot Selling Deep Drawing JIS Standard Silicon Steel Sheet . BBN hot sell Brand specifications of Cold Rolled Steel . Brand specifications of Cold Rolled Steel Sheet Coil Brand For deep drawing. nipponsteel Steel ALSHEETTMstainless steel sheets to cope with exhaust gas restrictions, and inexpensive materials JIS G 3314-2018 (abstract) Hot-dip aluminum-coated steel sheets and bands JIS G 3314-2018 (abstract) Hot-dip aluminum-coated steel sheets and bands deep drawing) SA1F Heat resistance (ultra-deep drawing) Code:Tensile test Tensile :strength Deep-drawing steels DD, DC and DX - Product informationExamples of applications for hot-rolled deep-drawing steels are body and structural parts, chassis parts and wheel rims. Due to their specifically designed surface structure and excel - lent formability cold-rolled steel grades are well-suited to the Issue:July 2018, version 1 Deep-drawing steels DD, DC and DX Product information Steel Content